100% OEM Authentic Nissan Parts
2150CC FIC NISSAN SKYLINE RB26 FUEL INJECTOR CLINIC INJECTOR SET (HIGH-Z)
This massive high performance injector is in a class of its own when low end throttle response and short pulse width control is required. State of the art Data Match Technology dynamic flow matching is used during the production of these injector sets due their large flow rate. This significantly improves the ECUs ability to control these injectors in the sub 2ms pulse width area, typical of idle and part throttle conditions.
Each injector is individually serial numbered and the results are provided on the Data Match Sheet providing the most complete flow matching and latency value information available in the industry today.
Fuel Injector Clinic injectors are flow tested and rated at 43.5psi (3Bar) at 90 degrees F fuel temperature using CF-16B calibration fluid.
CAUTION! The internal construction of this 2150cc/min injector includes a seal that has been found to swell when in contact with MTBE from oxygenated fuels like Q16 or VP Import. This swelling causes a significant reduction in flow through the injector and therefore renders it unsuitable for use with MTBE oxygenated fuels. Please be sure to follow the care instructions for these injectors since there are potential corrosion issues that may arise from prolonged disuse while exposed to alcohol based fuels (E85, etc.)
Fuel Injector Clinic injectors are set up to and include all o-rings needed to fit the factory application for the listed vehicle. For aftermarket or other unusual setups please contact us prior to placing your order to make sure you receive injectors that fit properly.
Every injector is covered against failure caused by defects in original manufacture by our lifetime warranty.
This injector set is precisely matched using Fuel Injector Clinic's proprietary Data Match Technology. Each injector is individually serial numbered and the results are provided on the Data Match Sheet providing the most complete flow matching and latency value information available in the industry today.
Fuel Injector Clinic injectors are flow tested and rated at 43.5psi (3Bar) at 90deg F fuel temperature using CF-16B calibration fluid.
Superior short pulse width control and state of the art matching make these injectors easy to tune and provide great drivability.
Fuel Injector Clinic injectors are set up to and include all o-rings needed to fit the factory application for the listed vehicle. If you are using aftermarket or other unusual setups please contact us prior to placing your order to make sure you receive injectors that fit properly.
Every injector is covered against failure caused by defects in original manufacture by our lifetime warranty.
This set of injectors requires you to change the injector plug on the wiring harness in your car. This can be done by soldering in the pigtails (included with purchase) to replace the plugs currently on your harness, or you can choose to purchase the optional plug-n-play adaptors which will convert from the type of plugs on these injectors to the plugs on your harness without any need for cutting or soldering.
This plug conversion is made necessary because FIC always chooses to provide brand new, unused injectors for its performance applications. We do not believe that increasing the chance of a failure due to using remanufactured or core program based injectors is ever warranted.
2150CC FIC NISSAN SKYLINE RB26 FUEL INJECTOR CLINIC INJECTOR SET (HIGH-Z)
This massive high performance injector is in a class of its own when low end throttle response and short pulse width control is required. State of the art Data Match Technology dynamic flow matching is used during the production of these injector sets due their large flow rate. This significantly improves the ECUs ability to control these injectors in the sub 2ms pulse width area, typical of idle and part throttle conditions.
Each injector is individually serial numbered and the results are provided on the Data Match Sheet providing the most complete flow matching and latency value information available in the industry today.
Fuel Injector Clinic injectors are flow tested and rated at 43.5psi (3Bar) at 90 degrees F fuel temperature using CF-16B calibration fluid.
CAUTION! The internal construction of this 2150cc/min injector includes a seal that has been found to swell when in contact with MTBE from oxygenated fuels like Q16 or VP Import. This swelling causes a significant reduction in flow through the injector and therefore renders it unsuitable for use with MTBE oxygenated fuels. Please be sure to follow the care instructions for these injectors since there are potential corrosion issues that may arise from prolonged disuse while exposed to alcohol based fuels (E85, etc.)
Fuel Injector Clinic injectors are set up to and include all o-rings needed to fit the factory application for the listed vehicle. For aftermarket or other unusual setups please contact us prior to placing your order to make sure you receive injectors that fit properly.
Every injector is covered against failure caused by defects in original manufacture by our lifetime warranty.
This injector set is precisely matched using Fuel Injector Clinic's proprietary Data Match Technology. Each injector is individually serial numbered and the results are provided on the Data Match Sheet providing the most complete flow matching and latency value information available in the industry today.
Fuel Injector Clinic injectors are flow tested and rated at 43.5psi (3Bar) at 90deg F fuel temperature using CF-16B calibration fluid.
Superior short pulse width control and state of the art matching make these injectors easy to tune and provide great drivability.
Fuel Injector Clinic injectors are set up to and include all o-rings needed to fit the factory application for the listed vehicle. If you are using aftermarket or other unusual setups please contact us prior to placing your order to make sure you receive injectors that fit properly.
Every injector is covered against failure caused by defects in original manufacture by our lifetime warranty.
This set of injectors requires you to change the injector plug on the wiring harness in your car. This can be done by soldering in the pigtails (included with purchase) to replace the plugs currently on your harness, or you can choose to purchase the optional plug-n-play adaptors which will convert from the type of plugs on these injectors to the plugs on your harness without any need for cutting or soldering.
This plug conversion is made necessary because FIC always chooses to provide brand new, unused injectors for its performance applications. We do not believe that increasing the chance of a failure due to using remanufactured or core program based injectors is ever warranted.
Once your order ships, you'll receive a confirmation email with your tracking number and a link to track your shipment in real time. You can also track your order anytime by visiting the Order Status page using the link in your confirmation email. If you haven't received tracking info within 2–3 business days of your order, please contact us at Nizmopartsplug@gmail.com and we'll look into it right away.
We accept returns within 30 days of delivery on unused, uninstalled items in original packaging. A 20% restocking fee applies to eligible returns. Certain items are non-returnable, including electronic parts, special orders, and installed parts. Defective or incorrect items must be reported within 7 days. For full details, please review our Return Policy page before purchasing.
Yes — all parts sold on NizmoPartsPlug are brand new unless explicitly stated otherwise in the product listing. We source genuine OEM Nissan components and authentic aftermarket parts directly from trusted suppliers. If a part is used, refurbished, or a core charge item, it will be clearly noted in the product title and description.
Absolutely — if you don't see the part you need listed on our site, reach out to us at Nizmopartsplug@gmail.com or call us at (908) 265-4568 with the part number and we'll do our best to source it for you. We specialize in OEM Nissan and JDM components and have access to an extensive supplier network. Please note that special order parts may require a deposit and are non-returnable once ordered.
-
Store Pickup
Pickup available at Union, New Jersey
-
FAST Shipping
In Stock orders ship out Quickly
-
Secure Payment
Powered by Shopify and Stripe
Customer Reviews
See what people are saying
ONLY ORIGINAL MAINTENANCE PARTS
USE CODE : "RHDGUYS " AT CHECKOUT SAVE 5% ON MAINTENANCE PARTS
JDM to US License plate adapter bracket
A simple solution for mounting US plates on a JDM car. Don't drill holes in your license plate or your bumper! This simple plate bolts into the JDM plate frame and allows you to attach your US plate. It even comes with some nice stainless hardware and fancy washers!
Contact Us
Please fill out the form below and we’ll get back to you within 24 hours.
